QUESTION 29
Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.
Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

QUESTION 30
Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.
In this scenario, which two methods would be supported to migrate the data? (Choose two.)

QUESTION 31
On which type of network interfaces are the cluster interconnect LIFs created?

QUESTION 32
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer’s requests are satisfied?

QUESTION 33
You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.
In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

QUESTION 34
Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.
Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

QUESTION 35
You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.
In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)

QUESTION 36
You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.
Which tool would you use to accomplish this task?

QUESTION 37
Your customer wants to know more about the network configuration within the cluster.
In this scenario, which statement is correct about a LIF?

QUESTION 38
After completing the installation of an AFF A800 ONTAP AI cluster, you are asked which contacts are available for additional help in obtaining immediate assistance in solving P1 issues.
In this scenario, what do you tell the customer?

QUESTION 39
When you install a new ONTAP 9.7 4-node cluster, which network type is required?

QUESTION 40
Click the Exhibit button.

Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?

QUESTION 41
You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?

QUESTION 42
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer’s requirement? (Choose two.)

QUESTION 43
Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.
In this scenario, what would you tell the customer?

QUESTION 44
You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.
Which action must be taken to solve the problem?

QUESTION 45
Click the Exhibit button.

You want to add an AFF A400 system to an existing 4-node cluster.
Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.

QUESTION 46
Click the Exhibit button.

Immediately after installing a 4-node FAS8200 cluster, you discover that node, “cluster1-02”, must be removed from the cluster. You want to use the cluster remove-node command to remove the node.
Referring to the exhibit, which two statements are correct? (Choose two.)

QUESTION 47
Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.
Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

QUESTION 48
You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.
Which three tools do you need to complete this installation? (Choose three.)

QUESTION 49
Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

QUESTION 50
When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?